Seting NStreme dual slave mikrotk

I. MikroTik Device 1

1.1. Enabling wireless cards 1 and 2:

[admin@MikroTik] > interface enable wlan1
[admin@MikroTik] > interface enable wlan2

1.2. Assigning IP address to the ethernet interface:

[admin@MikroTik] > ip address add address=192.168.1.1/24 interface=ether1

1.3. Creating bridge interface:


[admin@MikroTik] > interface bridge add

1.4. Adding ethernet interface to the bridge interface:


[admin@MikroTik] > interface bridge port add interface=ether1 bridge=bridge1

1.5. Setting wireless cards 1 and 2 to nstreme mode:


[admin@MikroTik] > interface wireless set wlan1 mode=nstreme­-dual­-slave
[admin@MikroTik] > interface wireless set wlan2 mode=nstreme­-dual­-slave

1.6. Creating nstreme dual interface and setting Tx and Rx radios and frequencies:

[admin@MikroTik] > interface wireless nstreme­-dual add rx­-radio=wlan1 tx­-radio=wlan2
rx-­band=5ghz tx-­band=5ghz rx-­frequency=5180 tx­-frequency=5300

1.7. Adding nstreme interface to the bridge:

[admin@MikroTik] > interface bridge port add interface=nstreme1 bridge=bridge1

1.8. Checking the MAC address of the nstreme interface (in this example: 11:11:11:11:11:11):

[admin@MikroTik] > interface wireless nstreme­dual print
Flags: X ­ disabled, R ­ running
0 X name="nstreme1" mtu=1500 mac­address=11:11:11:11:11:11 arp=enabled
disable­running­check=no tx­-radio=wlan2 rx­-radio=wlan1 remote­mac=00:00:00:00:00:00
tx-­band=5ghz tx­-frequency=5300 rx­-band=5ghz rx­-frequency=5180
rates­b=1Mbps,2Mbps,5.5Mbps,11Mbps
rates­a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
framer­policy=none framer­limit=2560


II. MikroTik Device 2

2.1. Enabling wireless cards 1 and 2:


[admin@MikroTik] > interface enable wlan1
[admin@MikroTik] > interface enable wlan2

2.2. Assigning IP address to the ethernet interface:


[admin@MikroTik] > ip address add address=192.168.1.2/24 interface=ether1

2.3. Creating bridge interface:

[admin@MikroTik] > interface bridge add

2.4. Adding ethernet interface to the bridge interface:

[admin@MikroTik] > interface bridge port add interface=ether1 bridge=bridge1

2.5. Setting wireless cards 1 and 2 to nstreme mode:

[admin@MikroTik] > interface wireless set wlan1 mode=nstreme­-dual-­slave
[admin@MikroTik] > interface wireless set wlan2 mode=nstreme­-dual­-slave

2.6. Creating Nstreme dual interface and setting Tx and Rx radios and frequencies and setting the MAC address of the remote nstreme interface (in this example: 11:11:11:11:11:11 [step 1.8]):

[admin@MikroTik] > interface wireless nstreme­-dual add rx­-radio=wlan1 tx­-radio=wlan2
rx­-band=5ghz tx-­band=5ghz rx-­frequency=5300 tx­-frequency=5180
remote­mac=11:11:11:11:11:11 disabled=no

2.7. Adding nstreme interface to the bridge:

[admin@MikroTik] > interface bridge port add interface=nstreme1 bridge=bridge1

2.8. Checking the MAC address of the nstreme interface (in this example: 22:22:22:22:22:22):

[admin@MikroTik] > interface wireless nstreme­dual print
Flags: X ­ disabled, R ­ running
0 R name="nstreme1" mtu=1500 mac­address=22:22:22:22:22:22 arp=enabled
disable­running­check=no tx­-radio=wlan2 rx­-radio=wlan1 remote­mac=11:11:11:11:11:11
tx­-band=5ghz tx-­frequency=5180 rx-­band=5ghz rx-­frequency=5300
rates­b=1Mbps,2Mbps,5.5Mbps,11Mbps
rates­a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
framer­policy=none framer­limit=2560

III. MikroTik Device 1

1.9. Setting the MAC address of the remote nstreme interface (in this example: 22:22:22:22:22:22 [step 2.8]):

[admin@MikroTik] > interface wireless nstreme­-dual set nstreme1
remote­mac=22:22:22:22:22:22 disabled=no